After completing the IDMS 18.5 installation SMP/E jobs; I find the Installation Libraries IDMS185.CAGJCICS through IDMS185.CAGJXML however the CAISAG library is missing. How is the CAISAG library created?

Document ID : KB000057031
Last Modified Date : 14/02/2018
Show Technical Document Details

The IDMS 18.5 Installation can be accomplished via CA Chorus Software Manager (CSM) or manually from Pax-Enhanced Electronic Software Delivery (ESD). When using the manual method of installation; after completing the 18.0 SMP/E jobs, the installation libraries are created. These Installation libraries do not include the CAISAG library.  The CASAG library is created using member CFIG#JCL in the IDMS185.CAGJSRC library as documented in the CA IDMS Installation and Maintenance Guide:

In Chapter 5: Starting Your Product, in the section called "Configuring Your Product Without CA CSM" it provides the following steps: 


1. Create the CAISAG library (see page 72). 
2. Customize the CAISAG library members (see page 72). 
3. Execute the CAISAG program (see page 74). 
4. Review the configuration jobs generated by CAISAG. Repeat steps two to four until the configuration jobs are generated correctly for your site. 
5. Submit the generated configuration jobs. 

Then on page 72, it gives details on how to create the CAISAG library: 

Create the CAISAG Library: 
To allocate and populate a CAISAG library, customize and submit the CFIG#JCL member in your CAGJSRC library, which contains an IEBCOPY job. To customize this job, use the AGJSEDIT macro that you used to customize the SMP/E jobs. If you performed the SMP/E installation using CSM, you do not have an AGJSEDIT edit macro and need to customize the job manually. Then supply a prefix for the configuration data sets to be allocated on the SET statement. This job allocates a PDS with the low-level qualifiers CAISAG.CONFIG and populates it by copying four members from CAGJSRC. 

This is what the IDMS185.CAGJSRC(CFIG#JCL) should contain: 

//******************************************************************* 
//*** *** 
//*** This job allocates and populates the CAISAG library. *** 
//*** Customizing this job takes two steps. *** 
//*** *** 
//*** 1. Run the AGJSEDIT edit macro. This makes most *** 
//*** (all but one) of the required customizations. *** 
//*** *** 
//*** 2. In the SET statement below, specify a data set *** 
//*** prefix for allocating your CAISAG library. *** 
//*** *** 
// SET CFIGPFX=username.IDMSR185 CAISAG LIBRARY PREFIX 
//*** *** 
//******************************************************************* 
//* 
//IEBCOPY EXEC PGM=IEBCOPY 
//SYSPRINT DD SYSOUT=* 
//LIBIN DD DISP=SHR,DSN=your.IDMS185.CAGJSRC 
//LIBOUT DD DSN=&CFIGPFX..CAISAG.CONFIG, 
// DISP=(NEW,CATLG,DELETE), 
// VOL=SER=DASD04,UNIT=3390, 
// SPACE=(CYL,(2,1,65)), 
// DCB=(RECFM=FB,LRECL=80,BLKSIZE=8880) 
//SYSUT3 DD UNIT=SYSDA,SPACE=(TRK,1) 
//SYSUT4 DD UNIT=SYSDA,SPACE=(TRK,1) 
//SYSIN DD * 
COPY INDD=LIBIN,OUTDD=LIBOUT 
SELECT MEMBER=((CAISAG,,R)) 
SELECT MEMBER=((JOBCARD,,R)) 
SELECT MEMBER=((SETUP,,R)) 
SELECT MEMBER=((VARBLIST,,R)) 
/*