Adding or changing CADZSPLx and SAPI task processing criteria.

Document ID : KB000022788
Last Modified Date : 14/02/2018
Show Technical Document Details

Introduction:

The sample procedures below can be used to ADD tasks, DELETE tasks, or modify the processing criteria for the CADZSPLx and CADDSAPx (SAPI) tasks.

Instructions:

In EXAMPLE 1, The MSG and ARCH tasks had not yet been compiled into the CADZSPLx tasks ROOT LDS by the DDEXLDSI job when the product and LDS files were initially installed.

 We will be adding the MSG and ARCH task processing criteria into the CADZSPLx ROOT LDS as new tasks...

------------------------------------------------------------------------------------------------
------------------------------------------------------------------------------------------------

EXAMPLE 1:

  1. Log onto Dispatch and select option 8.1.
  2. On the VOPMI100 screen, tab down next to the MSG task and type an 'E' next to it and hit ENTER. This will END the task.
  3. On the VOPMI100 screen, tab down next to the ARCH task(s) and type an 'E' next to each one and hit ENTER. This will END the task(s).
  4. On the VOPMI100 screen, verify that the SAPIMSG, SAPIARCH, MSG and all ARCH tasks all show as: NOT ACTIVE OFF.
  5. Get out of Dispatch and go to the MVS Console to issue the following modify commands against the CADDSPLx task. Make sure you substitute the value of 'X' with the ACTUAL UNIQUE CADDSPL task SUFFIX.
  6. To add the MSG task and the SAPIMSG tasks processing criteria for CLASS=S and no destination, issue a:
/F SPLx,ADD MSG,CLASS=S,A=NOI

* The DEST parameter on an ADD statement is OPTIONAL and not required.

You should see the following messages:

CADD110I SPLx Operator=ADD MSG,CLASS=S 
CADD650I SPLx Adding/Updating Class/Dest information for MSG 
CADD651I SPLx Class/Dest information stored into CADDSPLx

To add the ARCH task and the SAPIARCH tasks processing criteria for CLASS=W and DESTINATION=WXYZ, issue a:
     /F SPLx,ADD ARCH,CLASS=W,DEST=WXYZ,A=INTERCEPT

You should see the following messages:

     CADD110I SPLx     Operator=ADD ARCH,CLASS=W,DEST=WXYZ,A=INTERCEPT 
     CADD650I SPLx Adding/Updating Class/Dest information for ARCH 
     CADD651I SPLx Class/Dest information stored into CADDSPLX

** You do not have to issue any commands to add the associated SAPI tasks. The processing criteria for the SAPI tasks will be added automatically by the above adds for MSG and ARCH.

If you want, bring down Dispatch first and then do a recycle of the CADZSPLx task and verify the MSG and ARCH tasks are now listed in your CADZSPLx task startup messages. Then bring Dispatch back up and go to the VOPMI100 screen and restart the MSG and ARCH tasks. Then try starting the SAPIMSG and SAPIARCH tasks.

------------------------------------------------------------------------------------------------
------------------------------------------------------------------------------------------------ 

In EXAMPLE 2, we will be deleting and re-adding the RPI2/SAPIRPI2 tasks with the new processing criteria of Class=V and Destination=MGM...

EXAMPLE 2:

  1. Log onto Dispatch and select option 8.1.
  2. On the VOPMI100 screen, tab down next to the RPI2 task and type an 'E' next to it and hit ENTER. This will END the task.
  3. If the status for the RPI2 task now shows 'RPI2 Not Act Off' skip to item #5.
  4. If the status for the RPI2 task now shows 'RPI2 Not Act ON' tab down next to it again and type an 'I' next to it to turn off dynamic intercept for this task and hit ENTER. The status must show as 'RPI2 Not Act Off' before proceeding.
  5. On the VOPMI100 screen, tab down next to the SAPIRPI2 task and type an 'E' next to it and hit ENTER. The status must show as 'SAPIRPI2 Not Active' before proceeding.
  6. Get out of Dispatch and go to the MVS Console to issue the following modify commands against the CADDSPLx task. Make sure you substitute the value of 'x' with the ACTUAL UNIQUE CADDSPL task SUFFIX.
  7. To delete the RPI2/SAPIRPI2 tasks, issue a:
/F SPLx,DEL RPI2                       

You should see the following messsages:

CADD110I SPLx     Operator=DEL RPI2                                 
CADD652I SPLx Removing Class/Dest information for RPI2              
CADD008I SPLx RPI2 Class V Dest MGM   has been deleted              
CADD653I SPLx Class/Dest information removed from CADDSPLx          

** You do not have to issue any commands to delete the SAPIRPI2 task. The processing criteria for the SAPIRPI2 task will be deleted automatically by the above delete for the RPI2 task.

To re-add the RPI2 task and the SAPIRPI2 tasks with the new processing criteria, issue a:

/F SPLx,ADD RPI2,CLASS=V,DEST=MGM,A=INTERCEPT                        

You should see the following messages:

CADD110I SPLx     Operator=ADD RPI2,CLASS=V,DEST=MGM,A=INTERCEPT                
CADD650I SPLx Adding/Updating Class/Dest information for RPI2
CADD651I SPLx Class/Dest information stored into CADDSPLX 
-------------------------------------------------------------------------------------------------
-------------------------------------------------------------------------------------------------